optoway SPM-5101G *********************************************************************************************************************************************************************** *********************************************************************************************************************************************************************** optoway technology inc. no .3 8, kuang fu s. road, hu kou, hsin chu industrial park, hsin chu, taiwan 303 tel: 886-3-5979798 fax: 886-3-5979737 e-mail: sales@optoway.com.tw http: // www.optoway.com.tw 12/15/2005 v3.1 1 SPM-5101G / spm-5101bg / spm-5101ag (rohs compliant) 3.3v / 1310 nm / 622 mbps lc sfp multi-mode transceiver ********************************************************************************************************************************************************************** features l hot-pluggable sfp footprint lc optical transceiver l small form-factor pluggable (sfp) msa compatible l 1310 nm transmitter l 0 to 1000 m transmission l ac/ac coupling according to msa l lv-ttl tx disable input signal l lv-ttl rx loss of signal output l single +3.3 v power supply l rohs compliant l 0 to 70 o c operating : SPM-5101G l -10 to 85 o c operating : spm-5101bg l -40 to 85 o c operating : spm-5101ag l class 1 laser international safety standard iec 60825 compliant applications l fast ethernet links l sonet / sdh equipment interconnect l fiber channel links description the SPM-5101G series is small form factor pluggable module for multi-mode fiber fast ethernet and oc-12 / stm-4 sonet / sdh fiber communications. it is with the sfp 20-pin connector to allow hot plug capability. the transmitter section uses a multiple quantum well 1310 nm laser and is a class 1 laser compliant according to international safety standard iec 60825. the receiver section uses an integrated ingaas detector preamplifier (idp) mounted in an optical header and a limiting post-amplifier ic. laser safety this multi-mode transceiver is a class 1 laser product. it complies with iec 60825 and fda 21 cfr 1040.10 and 1040.11. the transceiver must be operated within the specified temperature and voltage limits. the optical ports of the module shall be terminated with an optical connector or with a dust plug. order information p/no. bit rate (mb/s) distance (m) wavelength (nm) package temp. ( o c) tx power (dbm) rx sens. (dbm) rohs compliant SPM-5101G 622 0 to 1000 1310 lc sfp 0 to 70 -12 to -19 -26 yes spm-5101bg 622 0 to 1000 1310 lc sfp -10 to 85 -12 to -19 -26 yes spm-5101ag 622 0 to 1000 1310 lc sfp -40 to 85 -12 to -19 -26 yes absolute maximum ratings parameter symbol min max units notes storage temperature tstg -40 85 o c operating temperature topr 0 -10 -40 70 85 85 o c SPM-5101G spm-5101bg spm-5101ag power supply voltage vcc 0 3.6 v input voltage --- gnd vcc v output current iout 0 30 ma recommended operating conditions parameter symbol min typ max units / notes power supply voltage vcc 3.1 3.3 3. 5 v power supply current i cc (tx+rx) 150 250 ma operating temperature topr 0 -10 -40 70 85 85 o c / SPM-5101G o c / spm-5101bg o c / spm-5101ag data rate 622 700 mb/s
optoway SPM-5101G *********************************************************************************************************************************************************************** *********************************************************************************************************************************************************************** optoway technology inc. no .3 8, kuang fu s. road, hu kou, hsin chu industrial park, hsin chu, taiwan 303 tel: 886-3-5979798 fax: 886-3-5979737 e-mail: sales@optoway.com.tw http: // www.optoway.com.tw 12/15/2005 v3.1 2 transmitter specifications (0 o c < topr < 70 o c, 3.1v < vcc < 3. 5v) parameter symbol min typ max units notes optical optical transmit power po -19 --- -12 dbm 1 output center wavelength l 1260 1310 1360 nm output spectrum width dl --- --- 10 nm rms ( ) extinction ratio e r 8.2 --- --- db optical rise time t r 2 ns 10% to 90% values optical fall time t f 2 ns 10% to 90% values relative intensity noise rin -116 db/hz total jitter tj 1.0 ns 2 electrical data input current C low i il -350 m a data input current C high i ih 350 m a differential input voltage v ih - v il 0.5 2.4 v peak-to-peak tx disable input voltage C low t dis, l 0 0.5 v 3 tx disable input voltage C high t dis, h 2.0 vcc v 3 tx disable assert time t assert 10 m s tx disable deassert time t deassert 1 ms tx fault output voltage -- low t faultl 0 0.5 v 4 tx fault output voltage -- high t faulth 2.0 vcc+0.3 v 4 notes: 1. output power is power coupled into a 62.5/125 m m multi-mode fiber. 2. measured with a 2 7 -1 prbs. 3. there is an internal 4.7k to 10k ohm pull-up resistor to vcctx. 4. open collector compatible, 4.7k to 10k ohm pull-up to vcc (host supply voltage). receiver specifications (0 o c < topr < 70 o c, 3.1 v < vcc < 3. 5v) parameter symbol min typ max units notes optical sensitivity --- --- --- -26 dbm 5 maximum input power pin -8 --- --- dbm signal detect -- asserted pa --- --- -26 dbm transition: low to high signal detect -- deasserted pd -43 --- --- dbm transition: high to low signal detect -- hysteresis 1.0 --- db optical return loss orl 14 db wavelength of operation 1260 1600 nm electrical differential output voltage v oh C v ol 0.6 2.0 v output los voltage -- low v ol 0 0.5 v 6 output los voltage C high v oh 2.0 vcc+0.3 v 6 signal detect assert time as max 100 m s off to on signal detect deassert time ans max 300 m s on to off notes: 5. minimum sensitivity and saturation levels at ber 1e-10 for a 2 23 -1 prbs. 6. open collector compatible, 4.7k to 10k ohm pull-up to vcc (host supply voltage).
optoway SPM-5101G *********************************************************************************************************************************************************************** *********************************************************************************************************************************************************************** optoway technology inc. no .3 8, kuang fu s. road, hu kou, hsin chu industrial park, hsin chu, taiwan 303 tel: 886-3-5979798 fax: 886-3-5979737 e-mail: sales@optoway.com.tw http: // www.optoway.com.tw 12/15/2005 v3.1 3 connection diagram pin signal name description pin signal name description 1 tx gnd transmitter ground 11 rx gnd receiver ground 2 tx fault transmitter fault indication 12 rx data out- inverse receiver data out 3 tx disable transmitt er disable (module disables on high or open) 13 rx data out+ receiver data out 4 mod-dfe2 modulation definition 2 C two wires serial id interface 14 rx gnd receiver ground 5 mod-def1 modulation definition 1 C two wires serial id interface 15 vcc rx receiver power C 3.3v 5% 6 mod-def0 modulation definition 0 C ground in module 16 vcc tx transmitter power C 3.3v 5% 7 n/c not connected 17 tx gnd transmitter ground 8 los loss of signal 18 tx data in+ transmitter data in 9 rx gnd receiver ground 19 tx data in- inverse transmitter data in 10 rx gnd receiver ground 20 tx gnd transmitter ground module definition module definition mod-def2 pin 4 mod-def1 pin 5 mod-def0 pin 6 interpretation by host 4 sda scl lv-ttl low serial module definition protocol module definition 4 specifies a serial definition protocol. for this definition, upon power up, mod-def(1:2) appear as no connector (nc) and mod-def(0) is ttl low. when the host system detects this condition, it activates the serial protocol. the protocol uses the 2-wire serial cmos e 2 prom protocol of the atmel at24c01a/02/04 family of components.
optoway SPM-5101G *********************************************************************************************************************************************************************** *********************************************************************************************************************************************************************** optoway technology inc. no .3 8, kuang fu s. road, hu kou, hsin chu industrial park, hsin chu, taiwan 303 tel: 886-3-5979798 fax: 886-3-5979737 e-mail: sales@optoway.com.tw http: // www.optoway.com.tw 12/15/2005 v3.1 4 recommended circuit schematic 10nf 10 f 10nf 10 f veer post amp ld driver z=50 z=50 z=50 z=50 veet 1 h 1 h td - td + vcct vccr rd - rd + 100 sfp module serdes 100 los rd - rd + td - td + 10nf 10 f protocol eeprom module detect scl sda loss of singal tx_disable tx_fault mod_def(0) mod_def(1) mod_def(2) 4.7k to 10k 4.7k to 10k 4.7k to 10k 4.7k to 10k tx_fault tx_disable (1,17,20) 3 2 18 19 16 15 12 13 8 (9,10,11,14) 6 5 4 4.7k to 10k vcc 3.3v vcc 3.3v ic ic depending on serdes package diagram units in mm
|
